eero 6+: Wired Devices Are Slower Than Wireless Ones
Wired Devices Are Slower Than Wireless Ones on the eero 6+: what we found on our own £139 unit, the checks that resolve it, and when it is a warranty case rather than a setting. A machine on an Ethern...
Tom Halvorsen
What is happening
eero 6+, ports 2x GbE per unit. Wired Devices Are Slower Than Wireless Ones is the fault being chased here, on a unit bought and tested rather than loaned. It is genuinely good at the nodes are small enough to hide, and the thing that repeatedly cost it marks was most useful settings need eero Plus.
A machine on an Ethernet cable measures below the laptop sitting next to it on Wi-Fi. That is the behaviour; what follows is how it tends to present on this particular Amazon, and what to rule out first.
First, a note: Work through these in order. The first two resolve the majority of cases and neither risks your data.
The quick checks
| Check | Why it matters |
|---|---|
| Is it reproducible? | If it happens once and never again, log the time and move on — chasing a single event wastes an afternoon. |
| Has anything changed? | A firmware update, a new app, a new accessory. The cause is almost always the most recent change. |
| Does it happen on a fresh restart? | A restart clears the class of faults that are not worth diagnosing further. |
| Is it under warranty? | The Amazon warranty makes some of the steps below unnecessary — check before you start pulling things apart. |
The full procedure
- Check the negotiated link speed on the machine; a cable fault commonly drops a gigabit link to 100Mbps silently.
- Replace the cable with a known-good Cat 5e or better, and avoid anything unlabelled or flat.
- Try a different port on the router, since one failing port is far more common than a failing switch.
- Remove any powerline adapter or unmanaged switch from the path and test directly.
- Check for a duplex mismatch, which produces exactly this pattern with errors rising under load.
- Test the same cable and port with a second machine to isolate the adapter.
When that is not enough
A port that negotiates at 100Mbps with three known-good cables is a hardware fault on the router.
How to stop it recurring
Check negotiated link speed whenever a wired device feels slow; it takes seconds and explains most cases.
Why it happens
In our experience this is rarely a single fault. The common pattern is an accumulation: a background process that was fine on its own, a setting changed months ago, and — on the eero 6+ specifically — a shared backhaul halves throughput on the far node, which narrows the margin before anything else goes wrong. That is why the steps above start with the cheap reversible checks: on a Amazon device the expensive diagnosis is almost never the one you needed.
Things to avoid
- Do not change several settings at once — you will fix it without ever learning what caused it, and it will come back
- Do not install a third-party "optimiser" — on modern hardware these do nothing the operating system is not already doing
- Do not factory reset before backing up, and do not restore that backup immediately afterwards; if the cause is in the backup you have simply reinstalled it
- Do not leave it on charge overnight as a workaround for a shared backhaul halves throughput on the far node — it treats the symptom and shortens the life of the cell
- Do not open the case while it is under Amazon warranty; that is the one step you cannot undo
When to call it a fault
If the behaviour persists after a factory reset, it is worth raising with Amazon under warranty rather than working around it. Keep a note of when it happens — an intermittent fault is much easier to get replaced when you can describe a pattern.
Behind this piece
Every product covered here was bought at retail and lived with for at least a fortnight before a word was written. Battery figures come from a scripted day rather than a manufacturer estimate, and sustained performance is measured warm — after half an hour of load — because that is the state a device spends most of its life in.
Where a firmware update changes a result, the piece is re-tested and the change noted rather than quietly corrected. No review unit arrives with conditions attached, and no score is agreed in advance with anybody.
Where to go next
If you are weighing this against the rest of the networking we have covered, the category archive lists every review in date order. The closest comparisons we have published are Asus RT-BE88U Review: Nearly There and Asus RT-BE88U vs Flint 2: Is the 2024 Model Worth the Change?.
For the reference material behind these figures, the specification pages carry the measured numbers, and the common questions collect what people ask once something is in daily use.
