What Fast Charging Really Does to a Battery (Aqara Presence Sensor FP2)
What Fast Charging Really Does to a Battery explained, with the Aqara Presence Sensor FP2's own measured figures as the worked example: modern fast charging is thermally managed and staged. Heat, not...
Maya Okonkwo
In brief
Aqara Presence Sensor FP2, extras Light sensor — What Fast Charging Really Does to a Battery. Measured on hardware rather than argued from theory, on a device we rate for zone mapping so one sensor covers several areas.
Modern fast charging is thermally managed and staged. Heat, not speed, is what actually degrades a cell.
Why this matters: Battery anxiety drives a lot of poor advice, including habits that make degradation worse rather than better.
How it actually works
Charging runs at its highest rate only in the lower part of the range, then tapers sharply. Firmware watches cell temperature and throttles current when it climbs. The damage curve is driven mainly by time spent hot and time spent at a very high state of charge, which is why charging in a hot car is worse than charging quickly.
What you actually notice
Take the Aqara Presence Sensor FP2 as a worked example. PIR sensors see movement; this sees people, which is a different thing entirely. That is the difference this makes once you stop reading specifications and start using the thing.
| Specification | Aqara Presence Sensor FP2 |
|---|---|
| Detection | mmWave presence, up to 5 zones |
| Protocols | Wi-Fi, Matter |
| Power | USB-C |
| Extras | Light sensor |
The same concept across four devices
One worked example is an anecdote. Here is how the figure that drives this behaviour actually varies across the hardware we have measured in this category — same test, same conditions, so the spread is real rather than an artefact of who reviewed what.
| Model | Detection | Price | Our score |
|---|---|---|---|
| Aqara Presence Sensor FP2 | mmWave presence, up to 5 zones | £74 | 4 / 5 |
| Nest Doorbell (wired, 2nd gen) | — | £179 | 4 / 5 |
| Eufy S3 Pro Cam | On-device AI | £219 | 4 / 5 |
| Meross Smart Plug Mini | — | £12 | 4 / 5 |
Where the line sits
It helps to have a number in mind before you start comparing. Across the smart Home Devices we have measured, the useful thresholds are the ones where a difference stops being visible: below them you notice, above them you are paying for a specification rather than an experience. The Aqara Presence Sensor FP2 reports mmWave presence, up to 5 zones for detection, which sits comfortably on the right side of that line, and Wi-Fi, Matter for protocols. Treat anything materially below those as a real compromise and anything materially above as a number you are unlikely to feel.
What people get wrong
- Charging overnight ruins a battery
- You should always discharge fully before charging
- A slower charger is always kinder to the cell
How to verify this at home
- Reproduce the conditions rather than trusting a one-off reading — run the same task three times and take the average.
- Note the figure your device reports and the figure it actually achieves; on the Aqara Presence Sensor FP2 those diverge under sustained load.
- Change one variable at a time. Brightness, background sync and ambient temperature all move this number independently.
- Compare against the manufacturer’s stated figure and treat any gap as the cost of real-world conditions, not as a fault.
- Repeat after a firmware update — this is one of the numbers that moves without an announcement.
Where it shows up on a spec sheet
On a smart Home Device listing this usually appears as the detection line — the Aqara Presence Sensor FP2 quotes mmWave presence, up to 5 zones. That figure is necessary but not sufficient: the protocols entry (Wi-Fi, Matter) constrains it in practice, and the two are almost never presented together. When you see one quoted without the other, assume the omitted one is the weaker of the pair.
What to do with this
Charge however is convenient, but keep the device cool and out of direct sun while it does.
Heat is the enemy, not watts.
Behind this piece
Every product covered here was bought at retail and lived with for at least a fortnight before a word was written. Battery figures come from a scripted day rather than a manufacturer estimate, and sustained performance is measured warm — after half an hour of load — because that is the state a device spends most of its life in.
Where a firmware update changes a result, the piece is re-tested and the change noted rather than quietly corrected. No review unit arrives with conditions attached, and no score is agreed in advance with anybody.
Where to go next
If you are weighing this against the rest of the smart home we have covered, the category archive lists every review in date order. The closest comparisons we have published are What Fast Charging Really Does to a Battery (Ecobee Smart Thermostat) and What Fast Charging Really Does to a Battery (Eufy S3 Pro Cam).
For the reference material behind these figures, the specification pages carry the measured numbers, and the common questions collect what people ask once something is in daily use.
